|
SageTV Software Discussion related to the SageTV application produced by SageTV. Questions, issues, problems, suggestions, etc. relating to the SageTV software application should be posted here. (Check the descriptions of the other forums; all hardware related questions go in the Hardware Support forum, etc. And, post in the customizations forum instead if any customizations are active.) |
|
Thread Tools | Search this Thread | Display Modes |
#1
|
||||
|
||||
Setup | Set Up Video Sources | Preview Works OK, but TV | Program Guide Does not?
I can preview channel 3.1 in Setup | Set Up Video Sources , no problem.
But Sage throws "No Signal" when I try to tune it in Program Guide. Also, the show's title in Program Guide (some sort of sitcom series) is obviously out of synch with the actual content being broadcast (a news show). Seems like I must have my tuner set up OK and it seems like at least part of SageTV is ok.... Can anybody point me to a possible problem area?
__________________
Server: SageTV 9, Windows 10, i5 NUC Clients: HD200*3 over Cat5e Ethernet + 1 slightly flakey HD 300 + 1 HD200 remote at another residence Plugins: (none yet, looking for recommendations) Storage: NetGear Ultra-6 NAS 10 TB total w/dual redundancy. Plus 5tb QNAP for RecordedTV. Capture: 3 Silicon Dust HomeRun tuner boxes (6 tuners total) Program Source: OTA antenna |
#2
|
||||
|
||||
Quote:
Don’t forget if you have a multi-tuner device that requires scanning for channels, you usually have to scan each tuner separately.
__________________
Server: Ryzen 2400G with integrated graphics, ASRock X470 Taichi Motherboard, HDMI output to Vizio 1080p LCD, Win10-64Bit (Professional), 16GB RAM Capture Devices (7 tuners): Colossus (x1), HDHR Prime (x2),USBUIRT (multi-zone) Source: Comcast/Xfinity X1 Cable Primary Client: Server Other Clients: (1) HD200, (1) HD300 Retired Equipment: MediaMVP, PVR150 (x2), PVR150MCE, HDHR, HVR-2250, HD-PVR |
#3
|
||||
|
||||
Quote:
For instance: (applies to all sub-channels) 3-1 KSBSCD [19-3-1] 3-1 KCDODT [23-3-1] 10-1 KSBSCD [19-10-1] 10-1 KCDODT [23-10-1] However, when I used HDHomeRun Setup to scan, only the 19-x-x was found. I, then, went back to SageTV Setup and found that the 23-x-x Channel was enabled and 19-x-x was disabled. When I switched that, everything worked as expected. I believe this is actually an issue with Schedules Direct and not with SageTV. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Program Guide Listings with two sources? | timg11 | SageTV EPG Service | 17 | 10-25-2017 08:39 PM |
Video Source Setup - No providers listed - Program Guide = No Data | calibrate | SageTV EPG Service | 14 | 10-21-2009 06:13 PM |
Channel Setup Preview works - Watch TV does not | MalibuDave42 | Hardware Support | 4 | 10-06-2009 04:29 AM |
Program Guide and Multi-Sources | TechBill | SageTV Software | 0 | 09-25-2007 04:11 AM |
2 Vid Sources, Same program guide data, different channel lineup? | rob.sfo | SageTV Software | 7 | 02-21-2007 08:36 PM |