|
|
|||||||
| Hardware Support Discussions related to using various hardware setups with SageTV products. Anything relating to capture cards, remotes, infrared receivers/transmitters, system compatibility or other hardware related problems or suggestions should be posted here. |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
01-01-2013, 01:11 PM
|
|||
|
|||
|
problem setup multiple hdpvrs
Trying to setup 2 hdpvrs on a server. Cannot remember how to do this correctly....
If I plug one in at a time I can successfully setup each one. However, whenever I have both plugged in it and go to setup the second it only sees the first one - never allows me to add the second. It acts as if I am editing the first. How do I configure two? Thanks in advance. 
|
|
#4
01-02-2013, 10:59 AM
|
||||
|
||||
|
@sflamm: Sage, Windows, and the Hauppauge are a bit finicky together. I've gone so far as to always make sure I power them up in the same sequence, among other things. Sometimes, I feel like I'm one of those guys in the NFL commercials... "It's only weird if it doesn't work".
 I have this issue with my Colossus not showing up in Sage and haven't been able to figure it out. I'm planning to reinstall Windows and Sage in that VM and start from scratch once I get that "other" issue you're aware of squared away.
__________________
Server: XP, SuperMicro X9SAE-V, i7 3770T, Thermalright Archon SB-E, 32GB Corsair DDR3, 2 x IBM M1015, Corsair HX1000W PSU, CoolerMaster CM Storm Stryker case Storage: 2 x Addonics 5-in-3 3.5" bays, 1 x Addonics 4-in-1 2.5" bay, 24TB Client: Windows 7 64-bit, Foxconn G9657MA-8EKRS2H, Core2Duo E6600, Zalman CNPS7500, 2GB Corsair, 320GB, HIS ATI 4650, Antec Fusion Tuners: 2 x HD-PVR (HTTP tuning), 2 x HDHR, USB-UIRT Software: SageTV 7
|
|
#5
01-02-2013, 04:15 PM
|
|||
|
|||
|
When I originally got the HD-PVR and wrote my "How to Guide", the best practice was to uninstall the SageTV software, install the HD-PVR in windows, and then reinstall SageTV. For some reason, Sage did a much better job of recognizing the hardware if it was not installed when the hardware was installed.
It could be that the SageTV service just needs to be stopped while installing the hardware, but uninstalling and re-installing Sage is simple enough and it ensured good results, so I never experimented with it much. It's been years since I wrote that, but I wouldn't be surprised if this still held true today.
__________________
i7-6700 server with about 10tb of space currently SageTV v9 (64bit) Ceton InfiniTV ETH 6 cable card tuner (Spectrum cable) OpenDCT HD-300 HD Extenders (hooked to my whole-house A/V system for synched playback on multiple TVs - great during a Superbowl party) Amazon Firestick 4k and Nvidia Shield using the MiniClient Using CQC to control it all
|
|
#6
01-02-2013, 04:24 PM
|
|||
|
|||
|
Might be useful for folks to have a pointer to your guide... avoid problems in the future.
At the time I was hooking this up I wasnt running SageTV as a service yet - so that wasnt a problem. Now of course I am ** Edit ** Didnt notice the guide is in the signature above
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| 2 HDPVRs | jerryb33 | Hardware Support | 6 | 11-29-2012 12:02 PM |
| 2 HDPVRs. One needs reboot | Jackal24 | Hardware Support | 22 | 08-11-2012 02:55 AM |
| Max HDPVRs and USBuirt? | heffneil | Hardware Support | 7 | 09-26-2010 04:59 PM |
| Multiple DirecTV STB's through HDPVRs? | BitBass | Hardware Support | 3 | 08-18-2010 09:39 PM |
| Sage losing communication with HDPVRs | srothwell | Hardware Support | 5 | 03-18-2010 09:59 AM |
Linear Mode
