|
|
|||||||
| Hardware Support Discussions related to using various hardware setups with SageTV products. Anything relating to capture cards, remotes, infrared receivers/transmitters, system compatibility or other hardware related problems or suggestions should be posted here. |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
02-10-2020, 04:23 PM
|
||||
|
||||
|
Trying to add new HDHomerun Tuner
Already have an HDTC-2US installed and running.'
Just hooked up a couple of HDHR5-2US tuners, but SagSetyo Vudeie does not seem to know about them: I navigate to Setup | Setup Video Sources and click Add New Source, but all it shows are the two tuners within the existing HDHR5-2US. Have I bought an incompatible model of tuner? Any thoughts on what I am doing wrong?
__________________
Server: SageTV 9, Windows 10, i5 NUC Clients: HD200*3 over Cat5e Ethernet + 1 slightly flakey HD 300 + 1 HD200 remote at another residence Plugins: (none yet, looking for recommendations) Storage: NetGear Ultra-6 NAS 10 TB total w/dual redundancy. Plus 5tb QNAP for RecordedTV. Capture: 3 Silicon Dust HomeRun tuner boxes (6 tuners total) Program Source: OTA antenna Last edited by PeteCress; 02-10-2020 at 04:26 PM. 
|
|
#2
02-10-2020, 04:58 PM
|
|||
|
|||
|
Quote:
 The HDHomeRun Setup program needs to be run before Sage can see the tuners. Launch HDHRSetup, check the Tuners tab and set the Source Type field for each new tuner. Be sure to click Apply. At this point, Sage should be able to see the tuners. I recall that it wasn't necessary to stop/restart Sage after updating HDHRSetup's config.
__________________
System #1: Win7-64, I7-920, 8 GB mem, 4TB HD. Java-64 1.8.0_141. Sage-64 v9.2.1 ATSC: 2x HDHR-US (1st gen white) tuners. HD-200. System #2: Win7-64, I7-920, 8 GB mem, 4TB HD. Java 1.8.0_131. Sage v9.1.6.747. ClearQAM: 2x HDHR3-US tuners. HD-200. System #3: Win7-64, I7-920, 12 GB mem, 4TB HD. Java-64 1.8.0_141. Sage-64 v9.2.1 ATSC: 2x HVR2250; Spectrum Cable via HDPVR & USB-UIRT. 3x HD-200. Last edited by JustFred; 02-10-2020 at 05:38 PM. Reason: emoji
|
|
#3
02-11-2020, 08:14 AM
|
||||
|
||||
|
Quote:
Your solution worked a-ok.... Now I have to figure why the vendor sent me those tuners instead of the ones I ordered - which, conceivably, could be out of production...
__________________
Server: SageTV 9, Windows 10, i5 NUC Clients: HD200*3 over Cat5e Ethernet + 1 slightly flakey HD 300 + 1 HD200 remote at another residence Plugins: (none yet, looking for recommendations) Storage: NetGear Ultra-6 NAS 10 TB total w/dual redundancy. Plus 5tb QNAP for RecordedTV. Capture: 3 Silicon Dust HomeRun tuner boxes (6 tuners total) Program Source: OTA antenna
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| hdhomerun prime as QAM tuner, only 1 tuner available | Deacon Crusher | Hardware Support | 7 | 02-19-2012 05:52 PM |
| HdHomeRun Tuner | Steve52 | Hardware Support | 4 | 02-16-2012 09:28 PM |
| Problem with one HDHomeRun tuner | WhiskeyLover | Hardware Support | 4 | 03-24-2011 06:58 AM |
| HDHomeRun Dual tuner | cdobbs | Hardware Support | 3 | 05-05-2010 07:12 AM |
| Adding HDHomeRun Tuner | smoothtlk | Hardware Support | 6 | 12-18-2007 04:32 PM |
Linear Mode
