|
|
|||||||
| Hardware Support Discussions related to using various hardware setups with SageTV products. Anything relating to capture cards, remotes, infrared receivers/transmitters, system compatibility or other hardware related problems or suggestions should be posted here. |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
01-30-2009, 09:54 PM
|
||||
|
||||
|
HD-PVR IR-Blaster stopped working
I installed 6.5.8, and discovered that channel changing of the cable box for HD-PVR recording doesn't work.
I went to the Source Set up for the HD-PVR, and checked Tuner Control. It is still set to Hauppauge IR Blaster StubDevice. Under "Change Tuning Device" there are no choices - only "Cancel". Under Test Infrared code, there are no options - only "Close". I reverted to 6.5.6 and it did not make any difference. I also recently changed to service mode I will try turning service mode off and see if it makes any difference. Debugging things by switching into and out of service mode is so irritating because all configuration settings are lost. But I have frequent UI crashes, and I'm tired of losing or interrupting recordings. It would be really nice to have one set of settings for both modes as a future enhancement.
__________________
HD300 extender with (2020 New Build) SageTV 64 bit V9.2.2.903 (service mode), Running on Windows 10 (64 bit), Intel Core i7-10700K CPU, 16G RAM, GIGABYTE Z490 UD motherboard. NVidia GTX1650 Super; Viewsonic LCD on one output and Mitsubishi WD57734 HDTV via DVI/HDMI on other output. HDHomeRun HDHR5-4US tuner, Hauppauge "Siena" 1512 HD-PVR2 connected to Cisco Cable modem from Spectrum, tuned with USB-UIRT. Last edited by timg11; 01-30-2009 at 10:11 PM. 
|
|
#2
01-30-2009, 10:10 PM
|
||||
|
||||
|
Now I'm back to 6.5.6 with service mode disabled. The HD-PVR channel changing is working again. It will change channels, but there is still nothing under Test Infrared code (there are no options - only "Close").
__________________
HD300 extender with (2020 New Build) SageTV 64 bit V9.2.2.903 (service mode), Running on Windows 10 (64 bit), Intel Core i7-10700K CPU, 16G RAM, GIGABYTE Z490 UD motherboard. NVidia GTX1650 Super; Viewsonic LCD on one output and Mitsubishi WD57734 HDTV via DVI/HDMI on other output. HDHomeRun HDHR5-4US tuner, Hauppauge "Siena" 1512 HD-PVR2 connected to Cisco Cable modem from Spectrum, tuned with USB-UIRT.
|
|
#3
02-02-2009, 01:34 PM
|
||||
|
||||
|
Does anybody have the HD-PVR IR blaster working in service mode? I read some issues with the USB-IRT, but I'm not sure if they apply to the HD-PVR blaster. I was running the service mode with user LOCALSYSTEM.
I would like to use service mode so I don't lose as many recordings due to SageTV UI crashes, but of course the HD-PVR has to be able to tune the cable box.
__________________
HD300 extender with (2020 New Build) SageTV 64 bit V9.2.2.903 (service mode), Running on Windows 10 (64 bit), Intel Core i7-10700K CPU, 16G RAM, GIGABYTE Z490 UD motherboard. NVidia GTX1650 Super; Viewsonic LCD on one output and Mitsubishi WD57734 HDTV via DVI/HDMI on other output. HDHomeRun HDHR5-4US tuner, Hauppauge "Siena" 1512 HD-PVR2 connected to Cisco Cable modem from Spectrum, tuned with USB-UIRT.
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| HD PVR Setup Question | Dean_H | Hardware Support | 13 | 01-09-2009 08:02 PM |
| HD PVR + Old Tuners = IR Blaster Fail | MakaMaka | Hardware Support | 2 | 12-28-2008 09:20 PM |
| HD PVR Woes | Striker:WG | Hardware Support | 4 | 12-01-2008 05:58 PM |
| HD PVR - Is it working ? | AtariJeff | Hardware Support | 3 | 11-01-2008 05:08 PM |
| Command to delay hd pvr for channel changing | bastian74 | Hardware Support | 1 | 10-20-2008 05:13 AM |
Linear Mode
