|
SageTV Software Discussion related to the SageTV application produced by SageTV. Questions, issues, problems, suggestions, etc. relating to the SageTV software application should be posted here. (Check the descriptions of the other forums; all hardware related questions go in the Hardware Support forum, etc. And, post in the customizations forum instead if any customizations are active.) |
|
Thread Tools | Search this Thread | Display Modes |
#1
|
|||
|
|||
Problem with changing channels
I use a USBUIRT to change channels and habve the inter digit gap set to 2 seconds.
Sage starts recording as soon as it sends the first digit. this causes 6 seconds of the previous channel to be recorded at the start of the new recording. This has led to some extremely explicit scenes from late night TV being recorded at the beginning of some childrens programs. The new channel can not be tuned in until the last digit is sent so is there a way for Sage to delay the start of the new recording until it has sent the final digit? Before you say its my fault these programs follow the normal program I was watching and as the tuner is not required for another channel it just stays on that channel before being switched to the new recording channel.
__________________
Server: ABIT IC7, P4 2.8 HT, 512MB, XP 2003, ABIT IC7, 2x100MB Lan, 2TB x 8 Disks, USBUIRT, PVR500, Composite from 2xSky boxes in a big box in my garage PVR: ABIT SG-80, Celeron 2.8, 512MB, XP Pro, 20GB Disk, 100MB Lan, USBUIRT, SKY+ remote control Client2: ABIT AL8, P4 3.0, 1024MB RAM, XP Pro. Client3: ABIT IC7, P4 2.4, 512MB RAM, XP Pro. Client4: ABIT AI7, Celeron 2.4, 512MB RAM, XP Pro. |
#2
|
||||
|
||||
There is a new property in v6.4:
mmc/encoders/<some number>/delay_to_wait_after_tuning Set it to the number of milliseconds to wait before starting to record. It is considered a bit experimental and SageTV cannot do anything else during this wait period, so the interface may appear to be locked during that time. - Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request. |
#3
|
|||
|
|||
This is great news. I'll check it out over the weekend, thanks.
__________________
Server: ABIT IC7, P4 2.8 HT, 512MB, XP 2003, ABIT IC7, 2x100MB Lan, 2TB x 8 Disks, USBUIRT, PVR500, Composite from 2xSky boxes in a big box in my garage PVR: ABIT SG-80, Celeron 2.8, 512MB, XP Pro, 20GB Disk, 100MB Lan, USBUIRT, SKY+ remote control Client2: ABIT AL8, P4 3.0, 1024MB RAM, XP Pro. Client3: ABIT IC7, P4 2.4, 512MB RAM, XP Pro. Client4: ABIT AI7, Celeron 2.4, 512MB RAM, XP Pro. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
HD PVR and Changing Channels Through Firewire | earl42 | Hardware Support | 1 | 11-04-2008 11:21 PM |
Set top stoped changing channels | kck | Hardware Support | 5 | 06-06-2007 09:04 AM |
Changing channels on comcast SDTV boxes | null_pointer_us | Hardware Support | 0 | 06-24-2006 03:29 PM |
USBUIRT Problems Changing Channels | mbrown3 | Hardware Support | 0 | 04-14-2006 07:21 AM |
STB not changing channels? | Steve52 | Hardware Support | 0 | 03-31-2006 05:46 PM |