|
|
|||||||
| SageTV Software Discussion related to the SageTV application produced by SageTV. Questions, issues, problems, suggestions, etc. relating to the SageTV software application should be posted here. (Check the descriptions of the other forums; all hardware related questions go in the Hardware Support forum, etc. And, post in the customizations forum instead if any customizations are active.) |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
10-06-2005, 08:05 PM
|
||||
|
||||
|
changing ff times not working
I like my skip forward set a 30secs and my back at 10 so I can skip forward with less presses and get a precise start of the show.
So, I edited sage.properties with sage off and the service stopped and I changed it to 30 secs, 30000 msecs and still I get 10 second skips, I even set it to 3 minute skips and I get nothing. Any idea why this isn't changing? Also I checked the sage.properties file, it is saving what I put in each time, not over-writing it. P.S. changing those times should be in the setup of the UI, even craptacular ATI media center had the ability to change those in the UI. 
|
|
#3
10-07-2005, 03:41 PM
|
|||
|
|||
|
Are you still using SageTv V. 2.x or are you using the Beta? If you're using the Beta did you get bit by the change in default install directories? I.e. it's in "/sagetv" now instead of "frey technologies/sagetv". If you've upgraded to the Beta and got bit by the install directory change you may be editing the wrong sage.properties file.
You are changing the right ff/rw right? There's a ff and a ff2 and both rw and rw2. I've got my ff2 and rw2 at 3 minutes and my ff and rw like yours at 30s ff and 10s rewind. They are working fine for me in the Beta and worked fine in the 2.2x I was using prior to using the Beta. That's why I'm suspecting the install dir mixup causing you to edit the wrong sage.properties file if you've gone to the Beta.
__________________
Wayne Dunham
|
|
#5
10-07-2005, 09:19 PM
|
|||
|
|||
|
I'm at a loss then. Sorry, I know it worked for me when I was running 2.2x.
__________________
Wayne Dunham
|
|
#6
10-07-2005, 10:07 PM
|
||||
|
||||
|
For anyone wondering what could be going on here with the properties file, see the middle of p. 15 in the v2.2 PDF manual. (p. 16 for the latest v3 beta)
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
#7
10-09-2005, 07:05 AM
|
|||
|
|||
|
Quote:
 Just another reason I don't use Service mode, it makes things too "complicated".
__________________
Wayne Dunham
|
|
#8
10-09-2005, 12:58 PM
|
||||
|
||||
|
Quote:
Thanks for the help, a mod can close this now. Last edited by roofus; 10-09-2005 at 01:06 PM.
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
