|
|
|||||||
| SageTV Software Discussion related to the SageTV application produced by SageTV. Questions, issues, problems, suggestions, etc. relating to the SageTV software application should be posted here. (Check the descriptions of the other forums; all hardware related questions go in the Hardware Support forum, etc. And, post in the customizations forum instead if any customizations are active.) |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
04-08-2005, 09:10 PM
|
|||
|
|||
|
SageTV Client 2.2: Error (-9): All encoders in use
When trying to use a single SageTV 2.2 Client I can only view the same channel as the host is currently tuned to.
When I try to change channels from the Client, the channel up/down arrows are grayed out, and, when I try to go to the EPG and use direct access to select a different channel, I get an error that reads in part: "Error (-9): All encoders in use by Clients playing "Live" TV" What should I do to enable the channel up/down arrows Client and EPG channel changing? Thanks!
__________________
Murray Kerdman 
|
|
#2
04-08-2005, 09:49 PM
|
||||
|
||||
|
Do you have multiple tuners? If not, I don't believe you can change the channel for live TV when multiple PCs are playing live TV. If you have multiple tuners, I thought it would switch to another tuner when the client changed channels, if there is a tuner available.
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
#3
04-08-2005, 10:02 PM
|
|||
|
|||
|
Quote:
What a brain fart I had. I am using a single tuner and not thinking. Of course it can only tune a single channel at any given time. I had the Host running while trying to use the Client too. Thanks!
__________________
Murray Kerdman
|
|
#4
05-01-2007, 10:02 AM
|
|||
|
|||
|
Opus,
I've been talking with Bob over here http://forums.sagetv.com/forums/show...170#post221170 about this same error message. I was wondering if you could check this out and see if there is a reason why I am getting this error message. I posted a debug file there too. Thanks in advance, Dana
__________________
Diehard SageTV User Hardware: Vizio M550NV 55",GA-H67A-UD3H-B3 LGA 1155, Intel i3, 4Gb DDR3, USB-UIRT, 2x Colossus, 1 HDHR, HD100, HD200 Software - Win7 64 bit, SageTV 7.1.9, Java v6, HD100 firmware v20100212-0, HD200 firmware 20100909 0
|
|
#5
05-01-2007, 11:22 AM
|
||||
|
||||
|
Quote:
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
